4K60 In-line Signal Re-Clocker with EDID Management

SKU: CON-H2-EDID

A multi-purpose installer tool, the CON-H2-EDID can perform a variety of tasks within an install. As an in-line device, it can act as an EDID manager to request specific content from a source, or as an audio de-embedder, extracting HDMI source audio via the S/PDIF or stereo mini-jack ports. Additionally, it can be a micro zone controller, sending CEC and RS-232 power triggers to connected projectors or screens and from its two relay ports, and can trigger devices in the zone using signal presence logic.

IN-LINE EDID EMULATOR
In a legacy installation scenario where EDID is not being communicated properly, the CON-H2-EDID can be connected in-line after the source device and using either a built-in or uploaded EDID file, can ensure the correct content is requested from the source.

AUDIO DE-EMBED
Compatible with any current content thanks to its 18Gbps and HDCP2.2 support, it can be placed in-line after any source device and extract the incoming audio via the 3.5mm jack or coaxial S/PDIF port.

MICRO ZONE CONTROLLER
Working on signal presence logic, the CON-H2-EDID can trigger a connected screen or projector on/off via both CEC or RS-232; the RS-232 commands can be entered via the configuration s/w tool that is part of WMS v1.6. Additionally, at the same time, it can trigger 3rd party motors (projector screens, lifts, blinds & curtains) via the built-in relays.

HDMI2.0 MAXED OUT
Sporting an 18Gbps HDMI input, the CON-H2-EDID can support all UHD video signals up to and including 2160p 4:4:4/60, and high frame-rate HDR 12bit 4:2:2 up to 60Hz.

Features

• In-line EDID manager with assignable presets or copy & import capability
• Assignable relays triggered on signal presence or via RS-232
• Source sensing power triggering:
• CEC: Compatible screens or projectors triggered manually via API or automatically on signal presence
• Serial: Power on/off commands can be stored and sent via RS-232 port
• Setup & configuration via simple PC configuration tool (WyreStorm Management Suite v1.6 or higher)
• Relay momentary or latching control
• Powered by 12v DC power supply (US, UK, EU and AU PSU pins included)
• Mounting brackets included
• USB-3-pin phoenix cable required for setup (not included) – Use P/n CAB-USB-PX1

Specifications

• Inputs:    1x HDMI In: 19-pin HDMI Type A Receptacle1x Audio In: 3.5mm TRS Stereo Jack Socket1x IR RX: 3.5mm TRS Jack Socket
• Outputs:    1x LAN (PoE): 8P8C “RJ45” Socket ANSI/TIA-5681x Audio Out: 3.5mm TRS Stereo Jack Socket1x USB Host: USB 2.0 Type B Receptacle1x RS-232: 3-pin Phoenix1x IR TX: 3.5mm TS Jack Socket

• Transmission Encoding:    Proprietary stream encoding. Video compression based on JPEG 2000Dante / AES67 compliant audio stream encoding
• End to End Latency:    With RX, 1 video frame (Passthrough mode) 2 video frames (scaling/video wall) e.g. 16ms @ 60Hz
• Max Transmission Bit Rate:    850Mb/s

• HDMI:    300MHz Max.TMDS Clock
• Maximum Data Rate:    8.91Gb/s HDMI
• Video Resolutions (Max):    1280x720p @60Hz 12bit 4:4:4/RGB1920x1080i @30Hz 12bit 4:4:4/RGB1920x1080p @60Hz 12bit 4:4:4/RGB3840x2160p @/30Hz 10/12bit 4:2:2/4:2:0 HDR10 HLG3840x2160p @30Hz 8bit 4:4:4/RGB3840x2160p @60Hz 8bit 4:2:0720x480p @60Hz 12bit 4:4:4/RGB720x576p @50Hz 12bit 4:4:4/RGB60fps Progressive 4:4:4/RGB: 640×480 | 800×600 | 1024×768 | 1280×800 | 1280×960 | 1280×1024 |1360×768 | 1366×768 | 1400×1050 | 1440×900 | 1600×1200 | 1680×1050 | 1920×1200Passthrough mode: Output at RX matches input at TX except for:1) YUV 4:2:0 converted to 8bit RGB2) For resolutions above 1920×1200 at 50/60Hz framerate is halvedScaler mode:User-selectable scaled output1) All formats converted to 8bit RGB2) Up to 3840x2160p @30Hz
• Supported Standards:    HDR10 | HLG | BT.2020 | BT.709 | 3D Video

• Audio Formats:    PCM up to 8ch | Bitstream audio formats including Dolby Atmos & DTS:X2ch Analog Dante: Up to 2ch PCM (HDMI) | 2ch Analog

• Ethernet:    IEEE 802.1ab 1000BASE-T
• HDCP:    HDCP 2.2 | 1.x
• EDID:    Programmable EDID | EDID Copy/Import | Custom EDID
• RS-232:    Programmable RS-232 Commands | Custom Command Generation (RX Only)
• IR:    Custom Command Generation
• Dante:    Full compatibility with Audinate control and management software tools for Dante

• Compatible Rack Mount Kit:    NHD-000-RACK4
• Included Accessories:    Wall Mount Brackets | Brackets for NHD-000-RACK4 | Infrared Cables | RS-232 Terminal Block
• Orientation:    Observe product chassis text

• Power Over Ethernet:    IEEE 802.3af (15.4W at PSE)
• External Power Supply:    Optional part: PSU-12V-1A
• Nominal Power Consumption:    8W

• Operating Temperature:    +32°F ~ +104°F (0°C ~ +45°C) | 10% ~ 90% non-condensing
• StorageTemperature:    -4°F to ~ 140°F (-20°C ~ +70°C) | 10% ~ 90% non-condensing
• Maximum BTU:    51.18 BTU/hr

• Rack Units/Wall Box:    <1U Flat on Shelf | 6U in NHD-000-RACK4
• Height:    25mm/1in
• Width:    220mm/8.67in
• Depth:    130mm/5.12in
• Weight:    0.75kg/1.65lbs

• Safety and Emission:    CE | FCC | RoHS | EAC | RCM